This kit utilizes the only OEM approved water methanol injection pump on the market with proprietary heat flange, twin seals, and custom motor winding to run cooler and longer than the competition. The Extreme Environment™ 300 PSI UHO Pump is designed to be in the elements with O-Ring connections that are then sealed and potted at our Colorado facility to ensure no moisture can enter the pump internals. Compare this to pumps that us a pump "sleeve". These sleeves will keep moisture around the pump unit leading to corrosion as well as trap heat to greatly decrease pump life. The Stage 1 comes standard with 100% methanol resistant components using stainless steel, nickel plating, EPDM, and hard anodizing to ensure years of continued use. Tie that in with new Snow Performance ACU-SEAL™ compression fittings for guaranteed leak free operation even when using 100% methanol. For a extremely robust, reliable water methanol injection experience that won't brake the bank look no further than the Snow Performance Stage 1 Boost Cooler™!
Unlock 50-70 HP on your boosted vehicle while decreasing your air temps by up to 100 degrees! Increase your pump gas octane by 25 points and make more power efficiently with a cooler running motor! The Snow Performance Stage 2.5 Boost Cooler™ water methanol injection kit is available for all forced induction applications (Supercharged/Turbocharged). The Stage 2.5 uses the progressive VC-50 controller (52mm Gauge) that proportionally injects more or less water methanol according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives a accurate delivery of water methanol and allows cooling and performance improvements over a wide range for improved drivability. Especially helpful for direct injected engines to remove 100% of carbon build up on the valves. Recommended for all street/strip driven forced induction vehicles using a turbo or centrifugal supercharger (Procharger/Vortech) looking for cooling over a wide range.
The VC-50 (ISO 9001 Manufactured) controller offers the functionality of a boost gauge and water methanol controller all in one! Highlighting a bright 7 color (Blue, White, Red, Yellow, Orange, Purple, Green) O-LED screen displaying boost, percentage of injection, low level, secondary stage activation, prime button, and system fault codes directly on the screen. You can tailor the controller color to match your OEM gauges or mix and match up to two colors!
The Snow Performance Stage 3 Boost Cooler® brings true 2D mapped water-methanol injection delivery to your EFI (electronic fuel injected) and forced induction (turbocharged/supercharged) vehicle. The Stage 3 creates a 2D injection map based off boost and fuel injector pulse width to deliver a extremely accurate amount of water-methanol when the engine needs it most. Bringing fuel injector pulse width into the mix allows the injection curve to be extended past specific boost points for greater range/control. None invasive, the Stage 3 Boost Cooler® controller is designed to mount on the steering column or the dash so no additional gauge pods need to be purchased and functions as a boost gauge, water-meth controller and fuel system monitor all in one! Proven to reduce the air inlet temperature by up to 100 degrees and increase octane by 25 points for maximum HP and cooling . Comes with adjustable Stage 3 water-meth controller, 1/4" High Temp Nylon line and easy to install quick-connect fittings.
Snow Performance now offers water-methanol injection with OEM level fuel system control for exact amounts of water-methanol to be delivered at any RPM range of the vehicle. The Stage 4 Boost Cooler™ utilizes engine RPM/Boost PSI to create a 2D fully adjustable water-methanol tune. Unlike any other system on the market the Stage 4 can give more or less water-methanol at any specific engine load state similar to a stand alone ECU. Using Snow Performance Platinum Tuning Software (free) the tuner can monitor, adjust water-meth delivery, data log/save files, and save/send completed water-methanol tunes to remote customers using a computer while on the dyno. Comes complete with Bosch MAP sensor, custom billet mount, USB cord, terminated wiring connections, LED alert system and 1/4" Nylon Tubing/quick-connect fittings. Recommended for all tuners looking for maximum water-methanol control.
Boost Juice™ is Snow Performance’s proprietary mix of 49% methanol and 51% water. It is made in a controlled environment with special care to make sure the ratios are accurate to result in a high performance water-methanol fluid formulated for use in the Boost Cooler™ injection system. Boost Juice is required as the exclusive fluid for lifetime warranty. *NOTE* Boost Juice CAN NOT be shipped outside of the United States. Boost Juice CAN ONLY be shipped using Ground service.
Sold in cases of four 1-gallon containers.
The Snow Performance Dual Nozzle Upgrade allows an additional nozzle to be mounted in any Snow Performance Boost Cooler kits. It includes a Tee, or splitter, junction piece with our quick-connect fittings, a nozzle holder and a section of hose. Note – injector nozzle is not included. Mounting additional nozzles are required when you need a quantity greater than one nozzle can provide, or if you have a dual plenum/throttle body/carburetor setup to get even distribution.
Snow Performance Shut Off Solenoid is used when mounting the injection nozzle lower than the reservoir or the reservoir is rear-mounted to prevent gravity flowing. It is also used to prevent siphoning when the injection nozzle is mounted after the throttle body or carburetor and is exposed to vacuum.
Snow Performance Nozzles are available in 60 ml/min, 100 ml/min, 175 ml/min, 225 ml/min, 375 ml/min, and 625 ml/min. Support 150-1500 HP.
Price reflects per nozzle.
